Pneumatic Resistance Butt Welding Machine

Pneumatic Resistance Butt Welding Machine

The Pneumatic Resistance Butt Welding Machine utilizes compressed air to deliver precise clamping and high-force axial upsetting during the resistance welding process. Developed for solid-state metallurgical joining of metal rods, wires, tubes, and profiled stock, this machine passes a high-amperage, low-voltage electrical current through the joint interface to generate localized heating. Once the abutting material ends reach their plastic forging temperature, pneumatic cylinders execute a continuous forging stroke, fusing the grain structures into a high-tensile joint. This equipment provides repeatable line speed and consistent structural integrity for high-volume metal fabrication, wire drawing preparation, and structural component manufacturing across carbon steel, stainless steel, and non-ferrous alloys.

Product Overview


The Pneumatic Resistance Butt Welding Machine utilizes compressed air to deliver precise clamping and high-force axial upsetting during the resistance welding process. Developed for solid-state metallurgical joining of metal rods, wires, tubes, and profiled stock, this machine passes a high-amperage, low-voltage electrical current through the joint interface to generate localized heating. Once the abutting material ends reach their plastic forging temperature, pneumatic cylinders execute a continuous forging stroke, fusing the grain structures into a high-tensile joint. This equipment provides repeatable line speed and consistent structural integrity for high-volume metal fabrication, wire drawing preparation, and structural component manufacturing across carbon steel, stainless steel, and non-ferrous alloys.

 

Working Principle


The pneumatic resistance butt welder joins metal components end-to-end through synchronized electrical resistance heating and pneumatic mechanical upsetting.


Workpiece Positioning & Clamping: The operator seats two workpieces into aligned copper alloy electrode jaws. Dedicated pneumatic clamping cylinders actuate, locking both ends under pressure along a shared center line to prevent axial slipping or angular displacement.


Resistance Heating Phase: The secondary circuit of the welding transformer delivers a low-voltage, high-amperage current across the abutting ends. High contact resistance concentrated at the joint interface rapidly converts electrical energy into localized heat, bringing the material ends to a forgeable plastic state.


Pneumatic Upsetting & Forging: At the pre-programmed heating interval, the moving platen is driven forward by a heavy-duty pneumatic upsetting cylinder. This high-speed axial force expels surface oxides and molten impurities from the interface, solidifying the continuous metallurgical grain structure.


Current Cut-off & Solidification: Welding current stops immediately upon upset initiation while pneumatic holding pressure remains engaged for a set duration, allowing the forged joint to cool without internal porosity before clamp release.

 

Key Features


Dual-Stage Pneumatic Force Control: Separate air pressure regulators control clamping cylinders and the upsetting cylinder independently, preventing thin-wall deformation while securing high upset forces during forging.


Precision Linear Motion Platen: The moving electrode assembly travels on precision linear guide rails with hardened steel ways, eliminating vertical play and maintaining concentric joint alignment down to low axial tolerances.


Digital Microprocessor Control Unit: Programmable controller manages multi-stage timing parameters-including pre-squeeze, impulse heating, upset delay, and post-weld annealing cycles-to handle varying material grades reliably.


Internal Liquid Cooling Architecture: High-conductivity water channels route directly through the welding transformer secondary loop, current-conducting blocks, and clamping jaws to maintain stable continuous-duty operating temperatures.


Hardened Copper Alloy Electrodes: Electrode holders feature quick-change copper alloy insert blocks resistant to high thermal loads and mechanical wear, minimizing maintenance downtime during long production runs.

 

Applications


Continuous Wire & Rod Drawing Lines
Joining coils of low-carbon steel, stainless steel, or aluminum wire stock prior to entry into continuous drawing machines, eliminating thread-up downtime and wire breaks.


Hardware & Tool Manufacturing
Welding ring structures, steel frames, buckets, shanks, and hand tool assemblies where joint tensile strength must match or exceed base material standards.


Automotive Wire & Cable Fabrication
Executing end-to-end connections on solid metallic rods, busbar stock, and structural wire harnesses requiring zero porosity and high shear resistance under vibration.


Appliance Frame & Grate Fabrication
Connecting wire outer rims, refrigerator shelf borders, and HVAC support frames that require flush joint profiles for subsequent grinding or powder coating.

 

Technical Specifications

 

Technical Parameter

Model: UN-25

Model: UN-50

Model: UN-100

Rated Input Voltage

AC 380V / 220V (50/60Hz)

AC 380V (50/60Hz)

AC 380V (50/60Hz)

Rated Capacity (50% Duty Cycle)

25 KVA

50 KVA

100 KVA

Primary Phase / Frequency

Single-Phase / 50Hz or 60Hz

Single-Phase / 50Hz or 60Hz

Single-Phase / 50Hz or 60Hz

Max. Upsetting Force

TBD (Pneumatic adjustable)

TBD (Pneumatic adjustable)

TBD (Pneumatic adjustable)

Max. Clamping Force

TBD

TBD

TBD

Max. Weldable Cross-Section (Low-Carbon Steel)

Up to 30 mm²

Up to 100 mm²

Up to 300 mm²

Weldable Diameter Range (Solid Steel Rod)

1.5 mm - 6.0 mm

3.0 mm - 12.0 mm

8.0 mm - 20.0 mm

Compressed Air Working Pressure

0.4 - 0.6 MPa

0.5 - 0.7 MPa

0.6 - 0.8 MPa

Cooling Water Consumption

4 L/min minimum

6 L/min minimum

10 L/min minimum

Control System Type

Microprocessor Digital Controller

Microprocessor Digital Controller

Microprocessor Digital Controller

 

Customization Options


Profile-Specific Clamping Jaws: Custom-machined copper alloy electrode jaws designed to hold non-circular geometries, including rectangular strips, hex bars, structural channels, and hollow tubes.


Integrated Pneumatic Flash Trimmer: Mounted secondary shear blades to clip or trim excess circumferential upset flash immediately after forging, before workpiece unclamping.


Multi-Impulse & Post-Annealing Controls: Extended controller firmware supporting current ramps and post-heat tempering pulses for high-carbon steel and alloy stock subject to hard joint brittleness.


Automated Pneumatic Workpiece Stops: In-line mechanical stops with pneumatic retraction to standardize material stick-out length and upset distance across manual operator shifts.

 

Sample Testing & Quality Validation


Sample Material Evaluation: Submit workpiece samples, material specification sheets, and joint tolerances for evaluation by welding application engineers.


Parameter Schedule Development: Test welds determine optimal pneumatic pressure profiles, current intensities, and heating durations to achieve full joint penetration without material burning.


Mechanical & Structural Validation: Welded trial samples undergo tensile pulling tests, bend testing, and cross-sectional metallographic examination to verify joint strength matching base metal requirements.


Data Log Sign-off: Complete parameter schedules and physical testing logs are provided for technical sign-off prior to machine order finalizing and shipment.

 

FAQ

 

Q: How does pneumatic clamping improve joint quality over manual foot-lever clamping mechanisms?

A: Pneumatic clamping supplies constant, measurable clamping pressure regulated via air valves. This prevents workpiece slippage during high axial upset pressure, ensuring consistent joint length and eliminating burn-marks caused by variable operator lever force.

Q: Can this machine join dissimilar metals such as copper to aluminum or carbon steel to stainless steel?

A: Yes, provided cross-sections and electrical conductivity parameters fall within range. Welding dissimilar metals requires tailored parameter setups, such as differential electrode extension lengths and multi-pulse heating, which can be validated during pre-order sample testing.

Q: What surface preparation is required on stock ends prior to pneumatic resistance butt welding?

A: Material ends should be square-cut with flat contact faces and free of heavy oil, scale, paint, or rust to ensure uniform electrical contact resistance across the entire cross-section.

Q: How is the circumferential weld flash removed post-welding?

A: Resistance butt welding creates an outward flash ring during the upset phase. This ring can be cleared using an optional integrated pneumatic flash trimmer, manual grinding, or dedicated inline deburring tool stations depending on output requirements.

Q: What facility utilities are required to operate this welder?

A: Operation requires a single-phase AC high-current power connection, clean dry compressed air delivered at 0.4 - 0.8 MPa, and a closed-loop water chiller supplying clean cooling water at 0.2 MPa minimum.

Hot Tags: pneumatic resistance butt welding machine, China pneumatic resistance butt welding machine manufacturers, suppliers, factory, 100 kva spot welding machine, inverter spot welding machine, mini tack welder, resistance spot welder auto body, spot welding machine automotive, spot welding usb

Send Inquiry